Stuff needs to go ASAP

~355 Block~(0 miles)
-2 bolt mains with ARP studs(for use with indluded windage tray)
-stock crank(new with 0 miles)
-forged scat rods with 7/16th bolts(not 3/8th)
-SRP -24cc inverted dome blower/turbo forged pistons
-plasma moly rings
-fully balanced
-new clevite teflon bearings throughout
-NO CAM.
-mellings HV pump with HP spring pick-up welded on and set to fit stock oil pan will be including with the sale of the motor.
--this engine will be awsome for any low compression turbo/supercharged setup. with trickflow 62cc heads/felpro 1074 gaskets the compression will come out to about 8.39:1..safe for 15psi
----this was my backup engine and I have all build reciepts. It cost me almost 1600$ JUST FOR the machine work not including the parts.(about 1500 in parts total)

$2050 shipped in any of the 48 states.
(will let it go for 1600$ PICKED UP this week only)
_____________________________________________
-MP70 Turbo w/.96 AR exhaust brand new in package SOLD

-Completely sand blasted (inside and out) to factory new condition and then hi-temp red paint)looks exactly like an LT4 intake...with polished top rails along with polished fuel rails and a polished stock TB with all sensors. SOLD.(you have to see how nice this thing looks inside and out)

-brand new 96 timing cover(lightly brush polished on the outside) with sensor and brand new crank/cam seal installed and comes with block to cover gasket-65$shipped

-Timing gears with reluctor wheel..38k miles on them along with brand new still in sealed plastic bag timing chain-65$shipped

-96/97 PCM has MADZ tune:cags(skipshift) delete 3.42 gears, GM847 cam, 30# injectors,6750 redline, 160 thermo, no speed limit, 875 idle,headers,rear o2/air delete,52mm tb-155shipped

-alternator-55shipped

-starter-55-shipped

-power steering pump/res/lines perfect condition(fittings are perfect too) 55$shipped

-AC delete pulley-55$(comes with accessory bracket)

-38k vented opti perfect condition-SOLD

-stock oil pan/with brand new oil pan gasket and support rails,55$(comes with plug too)

-stock replacement gm lifters(few hundred miles on them) SOLD.

-stock balancer. this balancer has been re-balanced to perfection, then sandblasted and professionaly painted factory black. I could tell you its brand new and youd never know the difference. balancer sold hub still avail for 20$.(96 hub and balancer)

-brand new never used SPEC BILLET flywheel. 255$shipped.(just paid 315 shipped for it a few weeks ago)

-bottom end gaskets,minus oil pan seal-(rear main and misc lower engine gaskets) 25$

-stock LT1 maf. took screen out havent run it with the screen. 55$

-lt1 bellhousing sandblasted to "factory new" condition. SOLD.

--98-02 front end possibly for sale. gm fenders(primered ready to paint, and primered LS1 Trans am front bumper with intercooler opening perfectly cut out..along with proper instal brackets might be for sale as well) i will post prices up on those later SOLD

-2 LT1 FRAME(not engine) motor mounts absolute perfect condition(sandblasted and repainted) 0 rust 0 chips in the paint.-55$shipped

-waterpump housing sandblasted in and out perfect for elec. water pump..looks better than brand new-SOLD....comes with blasted and brush polished thermo.

LT1 radiator. -65$shipped.

I will take pics of anything you need to see everything is exactly as described. Accept paypal and buyer will cover the 3.5% paypal charge.(also except postal money orders)

I have more but I cant think of anything else at the moment.

 

(will let car go without front end/drivetrain for 1100$

 

UpToTheTop

 

Where are you located?

 

connecticut.

 

do you have the alternator pulley?

 

yeah, it comes with the alternator.

 

willing to sell it seperatey?

 

no, I want to sell it all together. Thanks though.

 

Why are you selling all these pretty toys?

 

So I can play with my new toy. Rx7/LS1

 

how used is the radiator? guessing its for a 6speed car?96/97?

 

got any pics of the lifters?

 

no but I can take them. They are sitting in a container of oil.

 

sounds good bro