*UPDATED*

I am thinking about selling off a few parts I have lying around. I don't have to sell them so no low balling. Located in Southern NM.

LS1 intake setup: $250 shipped
SLP Lid
LS1 lower/radiator shroud
SLP smooth bellows w/NX shark nozzle

Breslin/Percy stainless steel locking header bolts. [The one with the allen head set screw that expands the bolt in the head] $25 shipped.

Weld Prostars 15x8 Rears. They have used Hoosiers on there now but I can take them off to ship. $285 shipped.

Comp Cam Solid Roller Lifters Used 888-16 $200 shipped.

Stock 1994 LT1 shortblock - 106,XXX.

I'm keeping the block but I am selling the rotating assembly - $100 + shipping

Stock 3.48 stroke Crank
GM Powder Metal (PM) Connecting Rods
Stock 4 valve releif pistons
Free with purchase *all used bearings!!!*

Stock LT1 camshaft - $45 shipped

Stock Timing Set - $15 shipped

Stock Oil Pump and Pickup - $20 shipped

Stock Oil Pan - $45 shipped

Stock 24lb Injectors - $25 shipped SOLD

39lb Cobra Injectors - Rated at 42/43 lbs in a LT1 w/ EV1 adapters - $165 shipped SOLD

Used Comp Cams CC306 - 230/244 .544/.576 112LSA - $175 shipped SOLD

Used Crane 10308 Valve Spring kit - These are good for over .600 lift. They are getting hard to find. A very reputable shop just checked them out and they are all within spec - $135 shipped. SOLD

New Lloyd Elliott [Elliott Portworks / Bullet Racing Cams] Custom Grind Billet Camshaft - 23X/24X .5XX/.5XX 113 LSA. Characteristics similar to a GM847. Ground for a very strong 355 or moderate 383. Real strong runner from 3800rpm up to 7000rpm. Designed for LE2 size Heads. Can use Crane 10308- springs listed above. $250 shipped. SOLD

3rd Gen 24mm Rear Sway Bar. Similar to the 25mm Spohn unit but without the cost. I have the u bolts and saddles for this.

USB Tuning Cable $40 shipped. OBDI. SOLD

Used - Custom 4" Aluminum Cold Air Intake - Comes with 4" K&N Filter. May have issues clearing ABS modules. - $85 shipped.

One Piece 5/16" pushrods 7.200" - $40 shipped

Stock LT1 lifters Two full sets - $40 shipped a set

Stock Front turn signals - $35 shipped

Mass Air Flow sensor stock LS1 - $50 shipped

Stock LT1 Flexplate - $35 shipped

Stock LT1 valve covers w/gaskets - $35 shipped

Stock LT1 Throttle Body 48mm - $35 shipped

TPIS Airfoil - $25 shipped or will include with Throttle body purchase for $15 SOLD

PICTURES: http://www.cardomain.com/ride/822569/3

-Dustin-

 

Pics of the cold air intake and headers? Interested in both.

 

I'm going to try and get some pictures tomorrow. I'm on a rough late night shift and I sleep through most of the daylight.

-Dustin-

 

pm'ed about headers.

 

did the motor smoke before you pulled it? and could you take pics. Very very interested in short block

 

whats the lowest you would take for the headers shipped?

 

No it never smoked, it ran so good I really don't want to tear it down.

Please see the updates.

-Dustin-

 

that le cam you think it would be good for a daily driver 383 or how street friendly is it..

 

Actually it would be perfect for a moderate 383. It would be the biggest usable power band for a 355, but perfect for a good performing 383 with heads and good compression. Your looking at peak power around 6300-6500. It's still going to need some stall and/or gear.

-Dustin-

 

I want to see pics of the CAI too.

 

Pictures added.

-Dustin-

 

TTT

-Dustin-

 

Updated.

-Dustin-

 

PM's replied.

-Dustin-

 

Looking to move this stuff.

-Dustin-